AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Steam vr desktop view standby streaming4/19/2023 However, there is no guarantee that interference will not occur in a particular installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Īny changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. DecaMove Battery Low/Charging: LED is steady redĭecaMove Battery level extremely (Sm (direct line of sight)įor more questions or suggestions, please reach us at:.DecaMove is turned on and connected to dongle: LED is blue.DecaMove ON but not connected to dongle: LED is Orangeĭongle connected to PC but not connected to DecaMove:- LED is steady red (com port open).To charge the DecaMove, please connect it to a USB port on your laptop or PC using the provided USB cable. ![]() ![]() Visit the Tips section for more info on how to use the DecaMove properly. You can turn it On or Off by clicking on the DecaMove button. We add an In-Game UI that shows your hip headings and the DecaMove battery gauge. It may take a bit of time to get used to this type of navigation control, especially if you are used to playing with controller-based movement, but it will give you an advantage against other non-DecaMovers. It allows you to navigate with your hip with minimal drift so that your movement direction can be independent of your headset or hand controllers. The DecaMove does one thing and it does it efficiently and accurately. Try pushing the left joystick forward to walk around, you will see that your movement is now relative to your hip. Without removing it, the movement will be wrong. locking the joystick in Contractors, or smoothing the joystick in Bone works). Once the game is running, go to the game settings menu and make sure that the locomotion method is set on continuous and head-oriented and set the dominant hand to right-handed.Īlso, depending on the game, remove any joystick manipulation mechanism (e.g. You will see the ? Calibrating message show up, hold the position until it’s complete. Then look forward and don’t move for 1 second. Make sure your hands point in the same direction as your head. ![]() Pavlov VR) A check mark next to it means that DecaMove supports this game.Ĭalibration is needed at the start of every gameplay session and at any time you feel the device heading has drifted.ĭecaMove’s gestured calibration does not require any special settings or any pressing of buttons: Simply hold your controllers close together in front of your hips. Go to the Home tab and click the game you want to play (e.g. In order to support many games without the need for the game developer to install the devices? SDK, it’s important that you launch games from Decatur. The DecaMove can be placed anywhere along the waist and hip area but we recommend placing it on the sides so that it doesn’t interfere with crouching Calibration is easy and should take less than 20 seconds, please follow the instructions in this link: The device? sensor fusion relies heavily on the magnetometer which MUST be calibrated before first use. Please refer to the troubleshooting section for any issues.ĭecaMove delivers precise, low latency, and high accuracy hip tracking. Pairing should happen automatically once the dongle is connected and theDecaMove is switched on. Notice the connection status changes to ? Streaming? and the compass icon rotates according to how you rotate your DecaMove. Turn on the DecaMove by pressing the button for 2 seconds.ĭecaMove LED will change from orange (not connected) to blue when it successfully connects to the dongle.
0 Comments
Read More
Leave a Reply. |